Zenith Data Systems SM-H-17-1 Manual de usuario descargar pdf (Pagina 5)

flOPPY

IMSK

DRIVE

INSET

•

5 S 5 H

INSET

•

ODD

5 S 5 H

INSET

•

ODD

~MSSSH

llKX'~21

)(

:1(~H

EJ-o-~"~

CUI

llKX'121S

lO<1

EJ-o~

"-EJ-C)-

CUI

llKX''121

II/uII

'':11

".Q-':J"',EJ.D

CUI

PROGRAMMING

MODULE

PROGRAMMING

MODULE

NOTE,

CONNECTOR

PINS

MUST REMAIN

"OPEN IUNSHORTENEDI.

.....

..1

•.

...

)

I......

;

PART

I.....

..1

I.....

..1

G·····..J

NOTE:

CONNECTOR

PINS

I ;

MUST

REMAIN

_,,,'OPEN

WNSHORTENEDI.

.....

..1

.•..•..

1 m

CUI

NOTE,

CONNECTOR

PINS

, ;

MUST

REMAIN

~'\pPEN

IUNSHORTENEDI.

.....

..1

.....

,.1

CUI

[......

......

PART

rr-,-------,

INSET

•

ODD

s 5 H

KX0l:21S

INSET

•

ODD

5 s 5 H

llKX'~21s

\("Cl\f

CO)[

INSET

•

ODD

5 s 5 H

X-;21S

om::

'>/

'II

EJ-o-,'V,~)~

COT

EJ-D-,W.~~

Il-=--=-=..

CUI

PROGRAMM I

MODULE

NOTE:

CONNECTOR

PINS

MUST

REMAIN

"OPEN lUNSHORTENEDI.

I......

;

PART

NOTE:

CONNECTOR

PIN~

MUST

REMAIN

."OPEN (UNSHORHNEDI.

.......

1 I

.......

CUI

.....

..1

.....

..1

NOTE:

CONNECTOR

PINS

MUST

REMAIN

"OPEN WNSHORTENEDI.

.....

..1

.....

..I~

-tl-,::::::::::::

CUT

PROGRAMMING

.......

1 1

.......

1 Q

MODULE

f j

I ;

If this drive is to be hardware

unit

0, either bend out

the leg of the programming module or cut the pro-

gramming module links as shown

Part A of Figure

2-2.

If this drive is to be hardware

unit

either bend out

the leg

the

programming module or cut the pro-

gramming module links as shown in Part C of Figure

2-2.

If you intend to use this drive with a double-density

controller, refer to Figure

2-2

(fold-out from this page)

for the following programming steps.

To set up a programming module, you may either

cut

the link on the module or bend out the appropriate

leg. The advantage of bending out the leg is that you

may return the module to its original state.

SOFT·SECTORED CONTROLLER

(Double-Density)

this drive is to

hardware

unit

either bend out

the leg of the programming module or cut the pro-

gramming module links as shown in Part Bof Figure

2-2.

SETUP

To sel

a programming

module.

you may

either

cui

the link on the moduie or bend out the

appropriate

leg. The advantage of bending out the leg is that you

may return the module to its original state.

HARD·SECTORED CONTROLLER

Programming

this drive is to be hardware unit 0, either bend out

the leg of

the

programming module or cut the pro-

gramming module links as

shown

Part A of Figure

2-1.

this drive is to be hardware

unit

2, either bend out

the leg of the programming module or cut the pro-

gramming module links as shown in Part C of Figure

2-1.

this drive is

hardware

unit

either

bend

out

the leg of the programming

module

or cut the pro-

gramming module links as shown in Part B of Figure

2-1.

you intend' to use this drive with the H·88-1 hard-

sectored controller (or with

H-17 controller in

H·B),

perform the steps under "Hard-Sectored Con-

troller." Refer to Figure

2-1

(fold-out from this page)

for

the

following

programming

steps.

Figure

2-1

Figure

2-2

1 2 3 4 5 6 7 8 9 10 ... 13 14

Comentarios a estos manuales

Sin comentarios

Zenith Data Systems SM-H-17-1 Manual de usuario Pagina 5

Comentarios a estos manuales